bennor said: presbuteros, Tomato has a logging feature, Status --> Logs. Perhaps reviewing the log will show why the two cameras became unreachable. DD-WRT also has a logging feature.
Bennor, yes that is a good idea but time wont allow me to troubleshoot. I loaded the following firmwares with connection issues or instability issues while trying to use two D-Link DCS920s:
Finally I loaded DD-wrt's dd-wrt.v24-18946_NEWD-2_K2.6_mega, configured and have run it for a full night with no hangups (all DCS920s still responding and sending video, all motion videos stored to the Samba shared USB 2 drive, all computers, NAS, and other elements still running on the network.) I admit that a configuration setting could have been off in Tomato firmware resulting in the failure; However, it was easier to load DD-wrt (configured the same as on Tomato) and it run stable. While I prefer Tomato's interface, I must run what is currently easiest to configure and deploy for my particular setup.
Finally got around to opening this up and installing DD-WRT mega on one of my two (I'll be putting DD-WRT on the other to use as a bridge). Install went smoothly.
Having a strange problem. I have been able to see and connect to the access point no problem from my iphone and Kindle. However, my MacBook Air laptops (running Lion) can't even see the SSID of the AP. Any ideas?
BostonOne said: Having a strange problem. I have been able to see and connect to the access point no problem from my iphone and Kindle. However, my MacBook Air laptops (running Lion) can't even see the SSID of the AP. Any ideas?
presbuteros said: BostonOne said: Having a strange problem. I have been able to see and connect to the access point no problem from my iphone and Kindle. However, my MacBook Air laptops (running Lion) can't even see the SSID of the AP. Any ideas?
Hope it helps... Thanks for that. That's a fix for connection problems with a network the machine can see & connect to. My problem is that my 2 laptops don't even see the SSID for the access point. Even if I try to enter it manually, it says "No network found."
BostonOne said: Finally got around to opening this up and installing DD-WRT mega on one of my two (I'll be putting DD-WRT on the other to use as a bridge). Install went smoothly.
Having a strange problem. I have been able to see and connect to the access point no problem from my iphone and Kindle. However, my MacBook Air laptops (running Lion) can't even see the SSID of the AP. Any ideas?
Running in mixed mode with WPA2 personal/AES. Problem solved. I had changed the channel to avoid interference with my neighbors - when I changed it back to Auto, the MacBook Airs could see the network.
BostonOne said: Problem solved. I had changed the channel to avoid interference with my neighbors - when I changed it back to Auto, the MacBook Airs could see the network. Did you set your channel above 11? If so, that would explain why it wasn't found. Even though the DD-WRT firmware will let you select channels 12, 13 and 14, those channels are not approved for usage in the US, and your wireless drivers probably won't bind to them.
Toddler said: BostonOne said: Problem solved. I had changed the channel to avoid interference with my neighbors - when I changed it back to Auto, the MacBook Airs could see the network. Did you set your channel above 11? If so, that would explain why it wasn't found. Even though the DD-WRT firmware will let you select channels 12, 13 and 14, those channels are not approved for usage in the US, and your wireless drivers probably won't bind to them.
Or it could have been something else. Yes, that was it. Though, interestingly enough, my iPhone & Kindle were still able to see the network & connect successfully.
I received a F7D7301 v1 and followed steps in the first post. Initially things appeared to move smoothly-- default factory settings, 30/30/30, bringing up cfe mini browser with the upload field -- this is done. But upon trying to upload the mini_f7d3301.bin, I get a problem loading page/"connection was reset" (in firefox) or "cannot display webpage (in IE). Also (after the 30/30/30), no light on the router is lit (although the cfe page does come up at 192.168.2.1).
Any tips to move forward would be great. Thanks.
Edit: Saw another post with the solution -- I used the Belkin default firmware to upload ddwrt, and it worked fine.
Now I have an issue with the retail packaging. Call it OT if you want. See, on the back of the packaging there is a picture at the bottom. In that picture, a girl is printing photos wirelessly, and another girl and a boy are looking together at the photos already printed. Now zoom on the second girl. While her shape is worthy of a picture, the way she sits on the bed and at the same looks at photos and smiles with the boy strikes me as unnatural.
Got the basic functionality going with ddwrt. It's bit of a letdown though to find out (from some of the posts) that enabling usb printers is such a bear on ddwrt. I've enabled all the usb options but no dice yet. Guess I need to ssh into the router and configure a bunch more.
On my 6-year old usr with default fw, configuring printers is a 30-second process. Enable usb port (radio button), and then begin pointing computers to the router's http://lan-ip-address/printer. One of the reasons I've hung on to this ancient router this long
If you decide to install ddwrt, expect that the usb printer/drive isn't click-and-go.
are u sure?, is any other problem you getting wih this file?
The router is sitting under my desk pretending it is a little 16gb ntfs wireless cloud at the moment. It has started speaking in voices, but that is more of a entertainment benefit than a problem.
You can get it here if you want to give it a spin. Link
--- /dev/discs/disc0/disc Block device, size 14.94 GiB (16039018496 bytes) DOS/MBR partition map Partition 1: 14.94 GiB (16038986240 bytes, 31326145 sectors from 63) Type 0x07 (HPFS/NTFS) NTFS file system Volume size 14.94 GiB (16038985728 bytes, 31326144 sectors) Status: Not mounted Status: Mounted on /mnt
scholar10 said: Got the basic functionality going with ddwrt. It's bit of a letdown though to find out (from some of the posts) that enabling usb printers is such a bear on ddwrt. I've enabled all the usb options but no dice yet. Guess I need to ssh into the router and configure a bunch more.
On my 6-year old usr with default fw, configuring printers is a 30-second process. Enable usb port (radio button), and then begin pointing computers to the router's http://lan-ip-address/printer. One of the reasons I've hung on to this ancient router this long
If you decide to install ddwrt, expect that the usb printer/drive isn't click-and-go. Getting the printing to work under DD-WRT is actually pretty simple. As posted back on page 16 of this thread here are the steps I used to get printing portion of my multi function USB printer to work.
Attach USB Printer to the router. Go to Services --> USB. Set USB Printer Support to Enable. Select the Save button, then select the Apply Settings button. (I rebooted the router just in case, don't know if needed).
Then follow the same directions TomatoUSB recommends for setting up a printer under their firmware, these steps work for DD-WRT... Configure Printer in Windows http://tomatousb.org/tut:configure-printer-in-windows
scholar10 said: If you decide to install ddwrt, expect that the usb printer/drive isn't click-and-go. It is with Tomato firmware. QOS (Quality of Service) is also very very good.
This is a statement not an act of flaming war. Disregard this statement if it insults you.
I can confirm what wizardking stated about NTFS working in the DD-WRT “big” firmware version. Using DD-WRT firmware dd-wrt.v24-18946_NEWD-2_K2.6_big.bin, here is results of a connected external USB NTFS drive. USB Support Disk Info --- /dev/discs/disc0/disc Block device, size 931.5 GiB (1000204886016 bytes) DOS/MBR partition map Partition 1: 931.5 GiB (1000202788864 bytes, 1953521072 sectors from 2048) Type 0x07 (HPFS/NTFS) NTFS file system Volume size 931.5 GiB (1000202788352 bytes, 1953521071 sectors) Status: Not mounted Status: Mounted on /mnt
USB printing works OK, as well. There were a few occasions when adding an external hard drive/flash drive where I had to power cycle the router to get the drives recognized and mounted, when using two or more drives connected to the router’s USB ports or via a powered USB hub connected to the router.
Only quirk so far (that I didn’t notice before) is a external Toshiba 1TB Canvio (HDTC610XK3B1) drive doesn’t power up when using USB Port 2 (left hand port) on the router. This drive works fine on USB Port 1 (right hand port). When I connect that drive to a powered USB hub and then connect the hub to USB Port 2, the drive is recognized and mounted. This quirk is probably due to the power draw on the Canvio drive being slightly out of USB 3.0/2.0 spec. This out of spec is the suspected cause of why this drive doesn’t work on some PC and MAC computers.
bennor said: scholar10 said: Got the basic functionality going with ddwrt. It's bit of a letdown though to find out (from some of the posts) that enabling usb printers is such a bear on ddwrt. I've enabled all the usb options but no dice yet. Guess I need to ssh into the router and configure a bunch more.
On my 6-year old usr with default fw, configuring printers is a 30-second process. Enable usb port (radio button), and then begin pointing computers to the router's http://lan-ip-address/printer. One of the reasons I've hung on to this ancient router this long
If you decide to install ddwrt, expect that the usb printer/drive isn't click-and-go. Getting the printing to work under DD-WRT is actually pretty simple. As posted back on page 16 of this thread here are the steps I used to get printing portion of my multi function USB printer to work.
Attach USB Printer to the router. Go to Services --> USB. Set USB Printer Support to Enable. Select the Save button, then select the Apply Settings button. (I rebooted the router just in case, don't know if needed).
Then follow the same directions TomatoUSB recommends for setting up a printer under their firmware, these steps work for DD-WRT... Configure Printer in Windows http://tomatousb.org/tut:configure-printer-in-windows
Outstanding! A minute after reading your post, I had wireless printing working. I withdraw all reservations about ddwrt.
The tomato link you provided is obviously key.
For some reason, my greening your post doesn't work...but I tried
Copy and paste the link. Let me rephrase that. I can't see why NTFS didn't make it into the mega build, since mega is supposed to be all-inclusive. Guess that's good news for you guys who need that feature.
Lurker1999 said: I can't get the link to work properly with the forum software. Here's a tinyurl link: http://tinyurl.com/yj2ygd
According to that link no dd-wrt version includes NTFS support, at least there is neither a dot by the big nor the mega versions. You're reading the wrong chart. Look at the K2.6 Build Features matrix.
Looks like the only difference between the mega and giga builds is lack of NTFS support in the former. Can the giga build be installed on this router or is there not enough memory?
bawaji said: Looks like the only difference between the mega and giga builds is lack of NTFS support in the former. Mega supports VPN Concentrate and SSH FTP.. Not a real deal breaker possibly for most..
Can the giga build be installed on this router or is there not enough memory?
I don't even see a Giga version of this DD-WRT build.. The routers built in memory is 8MB and the Mega build is already at 7.57MB..
I have went ahead and updated the Member Summary to reflect most of the contributions Fatwallet members have given this thread with direct links to the most common questions and solutions..
If you feel I left out something, please let me know and I will add it in..
Thank you to everyone who helped make this thread the most informative and supportive on Fatwallet!
Man, you did a great job. I replaced both my routers at home with this one. Unlike my previous netgear 2000 router, this one was so stable I didn't reboot it since flashed with dd-wrt a month ago. Also put my printer on it using optware. Put an external usb hard drive on second router which is my client bridge upstairs. It solved my hackintosh lacking wifi support problem. All the computers upstairs now got ethernet connections.
bennor said: scholar10 said: Got the basic functionality going with ddwrt. It's bit of a letdown though to find out (from some of the posts) that enabling usb printers is such a bear on ddwrt. I've enabled all the usb options but no dice yet. Guess I need to ssh into the router and configure a bunch more.
On my 6-year old usr with default fw, configuring printers is a 30-second process. Enable usb port (radio button), and then begin pointing computers to the router's http://lan-ip-address/printer. One of the reasons I've hung on to this ancient router this long
If you decide to install ddwrt, expect that the usb printer/drive isn't click-and-go. Getting the printing to work under DD-WRT is actually pretty simple. As posted back on page 16 of this thread here are the steps I used to get printing portion of my multi function USB printer to work.
Attach USB Printer to the router. Go to Services --> USB. Set USB Printer Support to Enable. Select the Save button, then select the Apply Settings button. (I rebooted the router just in case, don't know if needed).
Then follow the same directions TomatoUSB recommends for setting up a printer under their firmware, these steps work for DD-WRT... Configure Printer in Windows http://tomatousb.org/tut:configure-printer-in-windows
That looks pretty simple. I wish I would have tried that method. I ended up following the instructions here Link. The instructions are for an ASUS router but a previous link said that it would work with the Belkin. I can't believe I was able to follow it but I got mine working perfectly now.
I tried a couple of times to install Tomato instead but I was never able to get it installed. I tried multiple times with the same result: I updated the dd-wrt mini but on first login it would ask for a user and password (which I created) but when I tried to then log in to update to Tomato it would not accept the user or password that I created. I tried about 6 times before I decided to just use dd-wrt.
For $21 I've gotten an education into routers and dd-wrt.
BongWater said: bennor said: scholar10 said: Got the basic functionality going with ddwrt. It's bit of a letdown though to find out (from some of the posts) that enabling usb printers is such a bear on ddwrt. I've enabled all the usb options but no dice yet. Guess I need to ssh into the router and configure a bunch more.
On my 6-year old usr with default fw, configuring printers is a 30-second process. Enable usb port (radio button), and then begin pointing computers to the router's http://lan-ip-address/printer. One of the reasons I've hung on to this ancient router this long
If you decide to install ddwrt, expect that the usb printer/drive isn't click-and-go. Getting the printing to work under DD-WRT is actually pretty simple. As posted back on page 16 of this thread here are the steps I used to get printing portion of my multi function USB printer to work.
Attach USB Printer to the router. Go to Services --> USB. Set USB Printer Support to Enable. Select the Save button, then select the Apply Settings button. (I rebooted the router just in case, don't know if needed).
Then follow the same directions TomatoUSB recommends for setting up a printer under their firmware, these steps work for DD-WRT... Configure Printer in Windows http://tomatousb.org/tut:configure-printer-in-windows
That looks pretty simple. I wish I would have tried that method. I ended up following the instructions here Link. The instructions are for an ASUS router but a previous link said that it would work with the Belkin. I can't believe I was able to follow it but I got mine working perfectly now.
I tried a couple of times to install Tomato instead but I was never able to get it installed. I tried multiple times with the same result: I updated the dd-wrt mini but on first login it would ask for a user and password (which I created) but when I tried to then log in to update to Tomato it would not accept the user or password that I created. I tried about 6 times before I decided to just use dd-wrt.
For $21 I've gotten an education into routers and dd-wrt. Sounds like you did pretty well, especially for an old stoner.
BongWater said: I tried a couple of times to install Tomato instead but I was never able to get it installed. I tried multiple times with the same result: I updated the dd-wrt mini but on first login it would ask for a user and password (which I created) but when I tried to then log in to update to Tomato it would not accept the user or password that I created. I tried about 6 times before I decided to just use dd-wrt. When the Tomato firmware is flashed via the DD-WRT mini, Tomato does not use the DD-WRT username and password login information. The reason for this is the way DD-WRT stores the http_passwd variable. Tomato should default (as far as I've seen when flashing to TomatoUSB on the F7D7301) to the following login... Username: root Password: admin
Hello, any help would be much appreciated. I am unable to load mini build via CFE menu. Using Chrome. It shows "uploading 17%" or so, then after ~20 sec web page goes down showing HTTP status 503. After that dd-wrt does not come up (waited 10, 20 min.). I am able to re-boot router and do 30/30/30, and get back to CFE menu. Apparently dd-wrt did not load. Tried both 15396 and 18946 builds. Any suggestions?
andyh80 said: Hello, any help would be much appreciated. I am unable to load mini build via CFE menu. Using Chrome. It shows "uploading 17%" or so, then after ~20 sec web page goes down showing HTTP status 503. After that dd-wrt does not come up (waited 10, 20 min.). I am able to re-boot router and do 30/30/30, and get back to CFE menu. Apparently dd-wrt did not load. Tried both 15396 and 18946 builds. Any suggestions? Keep in mind that when you go to flash from the Belkin stock firmware right out of the box the router defaults to ip address 192.168.2.1. Once you flash the router with the DD-WRT Mini, the router should default to the IP Address 192.168.1.1. If your computer is configured for a static IP of 192.168.2.8 (per this thread's flashing directions) you will be unable to access the router when it has been flashed with DD-WRT mini. Change your computer's static IP address to 192.168.1.8, power cycle the router, wait at least a minute (the green light on the router should be on) then try to access the router again via 192.168.1.1 with your web browser.
Couple of comments/suggestions on flashing this router....
Never, EVER, flash this or any router over a wireless connection, always use a wired connection.
Clear your browser's Cache before flashing. Its important to delete the "temporary internet files" when deleting the browser's Cache.
If your computer has multiple network adapters, disable all but the one that is wired to the router.
Disconnect all other connected devices to the router including the broadband modem. This includes any connected USB devices.
Always configure your computer with a Static IP Address when flashing. Be sure to put the router's IP address in the Gateway field for the static IP address. The router should be reached at either 192.168.1.1 or 192.168.2.1 after being flashed.
Try an alternate browser if your current one cannot upload the firmware file from the CFE web page.
Always do a hard 30-30-30 reset BEFORE flashing the router. Press and hold the reset button for 30 seconds, while still holding in the reset button remove power to the router for 30 seconds, while still holding in the reset button, reapply the power to the router and wait 30 more seconds.
On the CFE page, select the option to reset or clear the NVRAM before flashing the router.
After the router firmware has been updated, power cycle the router.
Make sure your using the correct, recommened, firmware mention in this thread for this router, using incorrect firmware will brick this router.
Another way to reach the CFE page is to remove power from the router and press and hold the reset button, then reapply power and wait 30 seconds while continuing to hold in the reset button.
Don't be surprised if the router's indicator light is not lit when on the CFE page or when flashing from the CFE page to DD-WRT Mini.
If the router indicator light is orange (or any color other than green) after flashing, power cycle the router, and the router indicator light should return to green after a minute or two.
bennor said: andyh80 said: Hello, any help would be much appreciated. I am unable to load mini build via CFE menu. Using Chrome. It shows "uploading 17%" or so, then after ~20 sec web page goes down showing HTTP status 503. After that dd-wrt does not come up (waited 10, 20 min.). I am able to re-boot router and do 30/30/30, and get back to CFE menu. Apparently dd-wrt did not load. Tried both 15396 and 18946 builds. Any suggestions? Keep in mind that when you go to flash from the Belkin stock firmware right out of the box the router defaults to ip address 192.168.2.1. Once you flash the router with the DD-WRT Mini, the router should default to the IP Address 192.168.1.1. If your computer is configured for a static IP of 192.168.2.8 (per this thread's flashing directions) you will be unable to access the router when it has been flashed with DD-WRT mini. Change your computer's static IP address to 192.168.1.8, power cycle the router, wait at least a minute (the green light on the router should be on) then try to access the router again via 192.168.1.1 with your web browser.
Couple of comments/suggestions on flashing this router.... ...deleted list... I had to try multiple times with different browsers (with Cache clearing in between) to get the mini loaded. Initially, it looked like it wasn't doing anything after I chose to upload the image. This only happened with my 2nd router - I didn't have this issue with the first one.
Disclaimer: By providing links to other sites, FatWallet.com does not guarantee, approve or endorse the information or products available at these sites, nor does a link indicate any association with or endorsement by the linked site to FatWallet.com.
Members of our community may attach files to a post in accordance with the User Agreement. FatWallet is not responsible for the content, accuracy, completeness or validity of any information contained in any attached file. Files have *not* been scanned for viruses. Be especially wary of Excel files which may contain malicious content.
Shopping
Earn Cash Back while you shop - just 3 simple steps.
1. Sign Up so we know who to pay! (It's FREE.)
2. Shop through FatWallet for deals from your favorite stores. Your online purchases earn Cash Back that builds in your FatWallet account.
3. Get Paid by requesting a payment via check or PayPal.
FatWallet coupons help you save more when shopping online. Use our Coupons Search to browse coupons and offers from thousands of stores, gathered into one convenient location.
Forums
As part of our FatWallet Community, you can share deals with almost a million shoppers in our forums. Forum content is generated by consumers for consumers. Share deals, money-saving tips, and more. It's FREE, fun, and addicting.
Support
Our customer experience team is here around the clock - real people ready to assist.
